Tutorials Photoshop Photo Editing Create a stunning car showroom brochure

Create a stunning car showroom brochure

Use Photoshop to transform a digital photograph of your car into a flawless showroom brochure page.

The obvious thing to start with is an actual photograph of your car, we don't all have a photography studio large enough to house a vehicle and the equipment to capture a professional shot but an image from your average digital camera will do for this mockup. You can help enhance your shot by using a tripod at a low angle, and try and prevent any major reflections on the car bodywork.

The following brochure page mockup is an example outcome of this guide, combining your manipulated image with additional elements and sales blurb to produce an impactful promotional tool.

image 1
Click to enlarge

Open up your original image into Photoshop. If your image is going to be used for print in the long run, convert to CMYK and adjust the resolution as necessary.

image 2

Start off by drawing a path around the outline of the car, zoom right in and keep within a few pixels to prevent any background creeping in when the image is cut out.

image 3

image 4

Make a selection from your complete path, then Copy and Paste the vehicle on a new layer and fill the background black.

image 5

The image has quite a sharp outline from where it was cut out. Reselect the layer and Contract (Select > Modify > Contract) by 2px then Feather (Select > Feather) by 1px, Inverse (Ctrl+Shift+I) then delete. This should help the image blend in a little better.

Create a Black > Dark Gray gradient in the background to add a bit of depth to the image.

image 6

image 7

Duplicate your vehicle layer, then set the layer style to Multiply. This will transform the tones of the photograph and help it blend in with the dark surroundings. Merge down this layer (Ctrl+E) to combine the two vehicle layers. If you notice a highlighted outline appearing as a result simply repeat the Select > Contract & Feather procedure.

image 8

As you can see, the sky from the original photograph is still visible, zoom right in and draw paths around the windows, then Desaturate the selection (Ctrl+Shift+U).

image 9

image 10

Create a new layer and fill this selection a dark gray picked from the background. Setting this layer to Hard Light with around 75% Opacity will help blend in the windows.

image 11

Duplicate your vehicle layer, then flip vertically and position underneath the car to act as a reflection.

image 12

Draw a mask around the front section of the car's reflection and press Ctrl+T to Transform, use the Skew and Rotate options to bring the reflection parallel with the front of the car.

image 13

Adjust the Opacity as necessary (60%) and use a large eraser to fade out the reflection at the bottom.

image 14

The next step is to tidy up some of the reflections on the car, such as the tree showing through from the rear window.

Copy a section of the front side window and paste on a new layer. Position this selection over the tree branches and blend in as necessary with the eraser.

image 15

image 16

Repeat this process on the rear wing to remove the reflection of the buildings. Create a selection of a clean area of bodywork, Copy & Paste then adjust the Levels (Ctrl+L) and Hue & Saturation (Ctrl+U) to match the colour. Use the eraser to blend in.

image 17

image 18

image 19

Repeat this procedure on the other reflections to create smooth areas of colour. It may be necessary to copy multiple areas of different shades and blend them together. Use the Clone Stamp tool and Healing Brush to remove small blemishes and reflections.

image 20

Repeat this procedure again on the front bumper to remove the bright highlight, copy an area from the opposite side and use the Levels (Ctrl+L) to blend in.

image 21

image 22

Brighten up the wheels to make them a little more prominent, draw a selection around them both, then adjust the Levels (Ctrl+L). Don't forget to repeat on the reflected vehicle!

image 23

image 24

Draw a path around the headlights and adjust the Brightness & Contrast (Image > Adjustments > Brightness & Contrast) to give more of a crystal finish. Use the Hue & Saturation (Ctrl+U) to remove some of the blue tint. Repeat this step with circular selections of the fog lamps.

image 25

image 26

Draw another mask around the number plate and fill with a slight gradient using light shades of gray. Then add some text and use the Perspective, Skew and Distort from the Transform (Ctrl+T) palette to manipulate into shape. Don't forget to duplicate and place on the reflected vehicle too!

image 27

Finally layout the composition and add some additional elements to the artwork such as sales blurb from the manufacturer's website to finish off your showroom brochure page.

image 1
Click to enlarge

subscribe to newsletter